Window Screen Replacement Pasadena CA is the fix for torn mesh, bent frames, and screens that pop out of the track every time the wind picks up. We measure, cut, and re-spline on site, so you are not hauling frames across Los Angeles County. Most single-screen jobs are done in under an hour, and we carry pet-resistant and solar mesh on the truck for same-day swaps.
Window Screen Replacement Pasadena CA is the removal of a damaged screen frame or mesh and the installation of new spline, mesh, and hardware so the screen seats tight in the track again. We pull the frame, cut the old spline out with a screen repair tool, roll fresh mesh across the channel, and press it home with a concave roller. Corners get re-crimped, pull tabs get replaced, and every frame is test-fit before we call it done.
Pasadena homes take a beating from UV and dry heat. Vinyl spline dries out, aluminum frames pit, and standard fiberglass mesh turns brittle after a few summers. If your screens are dusty, sagging, or shredded at the bottom where the dog leans on them, that is normal wear for this climate. We see it constantly in Bungalow Heaven and along Orange Heights, where original wood windows still run the old-style screen channels.
Every screen replacement Pasadena California job includes the basics: mesh, spline, pull tabs, and a test fit. What changes is the mesh type and whether we reuse your frame or build a new one. Here is what is standard and what is an add-on.
We cut fresh mesh to size and drive new spline around the full perimeter. Standard 18x16 fiberglass is included. Pet-resistant, solar, and aluminum mesh are upgrades priced per screen. Old spline and mesh go with us, not in your trash.
Frames get checked on a flat table. If a corner is loose, we re-crimp it. If the frame is twisted beyond saving, we quote a new one before doing any mesh work, so you are not paying to re-screen a frame that will fail.
Missing or broken pull tabs get replaced so you can actually grab the screen without poking a finger through the mesh. We also check the latch and slide hardware on sliding screens and replace worn springs where needed.
While the screen is out, we vacuum the window track and wipe the sill with microfiber cloth. New mesh over a dirty track just gets re-dirtied. It is a small step that makes the finished job look complete instead of half done.
Every screen goes back into its own opening. We open and close the window, check the slide, and have you test it yourself. If anything rattles or binds, we fix it before we pack up. No paperwork until you are satisfied with the fit.
You call 877-318-1882 and tell us how many screens, what type of windows, and what is wrong. Torn mesh, bent frame, missing screen entirely. We ask about the neighborhood so we know what we are walking into, since a 1920s bungalow in Bungalow Heaven and a 1990s build in Hastings Ranch use different screen channels.
A technician arrives with a tape, a notepad, and samples of standard fiberglass, pet-resistant, and solar mesh. We measure every opening to the sixteenth of an inch and note the frame profile. If a frame is salvageable, we say so and re-screen it. If it is twisted or corroded, we quote a new frame on the spot.
Frames get squared and cleaned. We cut mesh with a half-inch overhang, seat it in the channel, and drive new spline with a screen repair tool. Solar and pet-resistant mesh get a slightly different roller pressure so the weave does not distort. Build time for a standard screen is about 10 to 15 minutes each.
Every screen goes back into its own opening, not a random one. We check the slide, the latch, and the pull tab, then open and close the window to confirm the screen clears the sash. If a screen rattles, we pull it and adjust the frame tension before moving to the next one.
You walk the house with us and open each screen yourself. We point out any frame we think will need replacing within a year so there are no surprises. Old mesh and spline go into our bucket, the track gets vacuumed, and we leave the sills wiped. Typical whole-house job takes two to four hours.
You call 877-318-1882 and tell us how many screens, what type of windows, and what is wrong. Torn mesh, bent frame, missing screen entirely. We ask about the neighborhood so we know what we are walking into, since a 1920s bungalow in Bungalow Heaven and a 1990s build in Hastings Ranch use different screen channels.
Used to lift old spline out of the channel and press new spline in without tearing the mesh. The concave profile seats the spline evenly around corners, which is where most DIY screen jobs fail.
Standard squeegees and scrapers for glass work done alongside screen replacement. We clean the glass while the screen is out so you are not washing around fresh mesh.
Used on larger panes and sliding glass doors where a wider squeegee cuts strokes in half. Faster work means less time with your windows open to the street.
Reaches second-story windows without leaning a ladder on your siding. Purified water dries spot-free, which matters on Pasadena's hard water. We use it on exteriors while screens are off.
For interior glass, sills, and tracks. Microfiber picks up dust instead of pushing it around, and Invisible Glass leaves no film. Used on every job before new screens go back in.
Removes paint overspray, sticker residue, and hard water spots from glass and frames. Common on post-construction jobs in Caltech and San Rafael where remodels leave marks on window components.
A lab and a shepherd had shredded the bottom third of four sliding door screens. Mesh was hanging in strips, and the frames were bent from the dogs pushing through. The homeowner was propping the doors open with a broom handle because the screens would not stay in the track.
After: We built four new frames with heavier aluminum stock and installed pet-resistant mesh with a deeper spline seat. All four screens now slide and latch properly. The homeowner tested each one by leaning on it. Total job time was about two hours.
Book this service →
A 1922 Craftsman had screens that were decades old. Spline was dried and cracked, mesh was brittle, and two frames were pitted at the corners. The homeowner wanted to keep the original look and was worried new screens would stand out.
After: We re-screened eleven screens with standard fiberglass mesh and replaced two frames cut to match the original profile. Tracks were vacuumed and sills wiped. The screens look period-correct from the street, and all eleven slide without rattling. Job took about three and a half hours.
Book this service →
Two small commercial units had nine door screens with torn mesh and missing pull tabs. Tenants had been taping the mesh back with packing tape for months. The property manager needed the work done without disrupting business hours.
After: We swapped all nine screens in one morning before the units opened, using heavier pet-resistant mesh on the doors and standard fiberglass on the windows. Pull tabs and latches were replaced. The manager got one invoice for the whole job instead of nine service calls.
Book this service →Most screen calls fall into a handful of categories. Here are the ones we see most often in Pasadena, and what happens if you leave them alone.
Ask a pro →We re-screen with pet-resistant mesh rated for claws and leaning. The weave is tighter and the spline sits deeper in the channel, so the screen holds up to daily abuse from dogs and cats. Most pet-resistant screens last three to five years in Pasadena sun.
We square the frame on a flat table and re-crimp the corners. If the frame is too far gone, we build a new one to the original opening size. New frames are cut from stock aluminum and crimped on site, usually within a quarter inch of the original.
We pull the old spline, clean the channel, and install new spline with proper tension. The mesh gets replaced at the same time, which restores airflow and stops the edge gaps. This is the most common fix we do in Pasadena, and it is usually the cheapest.
We build and install new screens for openings that never had them. We match the frame profile to the window and pick mesh that fits the room, standard fiberglass for bedrooms, solar mesh for west-facing rooms. Most homes are fully screened in one visit.
$45 - $180 per screen; $450 - $1,200 for most whole-house jobs
Screen replacement pricing in Pasadena is straightforward: you pay per screen, plus materials if you upgrade the mesh or need a new frame. Typical 2026 pricing runs $45 to $85 per screen for mesh replacement and $95 to $180 per screen for a new frame and mesh. Whole-house jobs usually land between $450 and $1,200 depending on screen count. We quote the full job before we start, so there is no surprise line item at the end. If you are comparing screen replacement service Pasadena California quotes, ask whether the price includes spline, pull tabs, and track cleanup. Ours does.
You are paying for mesh, spline, labor, and a proper test fit, not just a roll of screen material. A screen that is cut and splined correctly lasts years longer than a DIY job that lifts at the corners. We stand behind the work and fix anything that does not seat right.
Per-screen pricing drops slightly on larger jobs because setup time is spread across more screens. A single screen has a minimum trip charge. Twelve or more screens usually get a package rate. We quote both ways so you can see the difference.
Get a quote ↗Standard 18x16 fiberglass is the base price. Pet-resistant mesh adds $15 to $30 per screen. Solar screen material adds a similar amount and is worth it on west-facing windows that bake in the afternoon. Aluminum mesh for high-traffic doors costs a bit more.
Get a quote ↗If the frame is straight and the corners are tight, we re-screen it and you save money. Twisted, pitted, or crushed frames need replacement, which adds $50 to $95 per screen. We check frames on a flat table and tell you which category yours fall into.
Get a quote ↗Second-story screens take longer because of ladder setup and safety precautions. We follow OSHA safety compliance on every elevated job. Single-story homes in Bungalow Heaven are faster to work than two-story homes in Linda Vista, and the pricing reflects that.
Get a quote ↗“Our 1922 bungalow had screens that were original to the house, or close to it. Torn mesh, bent frames, the works. Rose City measured every opening, built new frames for four of them, and re-screened the rest. They were done in under three hours and the screens actually slide now. The technician pointed out two frames that would need replacing next year instead of upselling me on the spot.”
Marisol T.Homeowner, Bungalow Heaven
✓ Verified“Called about screen replacement near me in Pasadena after a windstorm shredded three screens on the west side of the house. They came out the next afternoon with pet-resistant mesh, since our lab leans on the sliding door screen. Price was $70 per screen plus a little more for the heavier mesh. No surprise charges, and they vacuumed the tracks before they left.”
Dennis K.Homeowner, Hastings Ranch
✓ Verified“I manage six small commercial units and the door screens get destroyed constantly. Rose City swapped nine screens across two buildings in one morning. They used heavier mesh on the doors and standard fiberglass on the windows. Invoicing was clean, they are licensed and insured, and they scheduled around our tenants instead of making everyone move their cars.”
Priya R.Property Manager, South Lake Avenue District
✓ VerifiedTypical 2026 pricing in Pasadena runs $45 to $85 per standard screen for mesh replacement, and $95 to $180 per screen if we build a new frame. Whole-house jobs on a 1,800 square foot home usually land between $450 and $1,200 depending on screen count and mesh type. Pet-resistant and solar mesh add $15 to $30 per screen. We quote the full job before we start, so the number you hear on the phone is the number on the invoice.
Yes. If the frame is straight and the corners are tight, we re-screen the existing frame and reuse it. That is the cheaper route, usually $45 to $85 per screen. We check the frame on a flat table first. If it is twisted, pitted, or the channel is crushed, re-screening will not hold, and we will tell you that instead of taking your money for a fix that fails in a month.
A single screen takes about 10 to 15 minutes to build and install. A whole-house job on 12 to 18 screens runs two to four hours on site. If we have to build new frames, add roughly 10 minutes per frame. Most Pasadena customers are back to open windows the same day. We schedule morning and afternoon routes, so you are not waiting around all day for a window.
We carry standard 18x16 fiberglass, pet-resistant mesh, solar screen material, and aluminum mesh for high-traffic doors. Fiberglass is the budget pick and handles most Pasadena homes fine. Pet-resistant mesh costs more but survives dogs and cats leaning on the screen. Solar mesh cuts heat and glare on west-facing windows, which helps in October when afternoon sun still hits hard. We bring samples so you can see the weave before you choose.
We are licensed, insured, and bonded, and we quote the full job before we start. Call 877-318-1882 and tell us how many screens you have and what is wrong with them. Same-day slots open most mornings.
Book Screen Replacement 877-318-1882 →Call 877-318-1882 or email us and we will get back to you the same business day. We answer the phone Monday through Friday, 8:00 to 18:00, and we take 24/7 emergency calls for broken glass and storefront cleanups. Tell us your address and roughly how many windows, and we will quote it.